專題文章 : L7954 SGSP-1.5P粉末螺旋絲攻M2~24(NEW)
| SGSP-1.5 螺 旋 式 絲 攻 NACHI SGSP-1.5P M LIST 7954 | |||||||||
 | |||||||||
| ● 食付形狀有效增加壽命 | |||||||||
| 單位:mm ●M2.0-24.0mm | |||||||||
| 規格 Thread Size | 等級 TAP Limit | 咬入 Lc | 全長 L | 螺紋 長度 | 溝數 N | 柄徑 Ds | 有效長 Ln | 有效直徑 dn | 形式 Type |
| M2*0.4 | P1.5 | 1.5 | 40 | 8 | 3 | 3 | 15 | 2.1 | 1 |
| M3*0.5 | P2 | 1.5 | 46 | 3.5 | 3 | 4 | 18 | 2.45 | 2 |
| M3.5*0.6 | P2 | 1.5 | 48 | 4.2 | 3 | 4 | 18 | 2.8 | 2 |
| M4*0.7 | P3 | 1.5 | 52 | 4.9 | 3 | 5 | 20 | 3.2 | 2 |
| M5*0.8 | P3 | 1.5 | 60 | 5.6 | 3 | 5.5 | 22 | 4.1 | 2 |
| M6*1 | P3 | 1.5 | 62 | 7 | 3 | 6 | 24 | 4.9 | 2 |
| M8*1.25 | P3 | 1.5 | 70 | 8.75 | 3 | 6.2 | 29.8 | 6.6 | 3 |
| M8*1 | P3 | 1.5 | 70 | 8.75 | 3 | 6.2 | 29.8 | 6.9 | 3 |
| M10*1.5 | P3 | 1.5 | 75 | 10.5 | 3 | 7 | 31.4 | 8.3 | 3 |
| M10*1.25 | P3 | 1.5 | 75 | 10.5 | 3 | 7 | 31.4 | 8.7 | 3 |
| M10*1 | P3 | 1.5 | 75 | 10.5 | 3 | 7 | 31.4 | 8.9 | 3 |
| M12*1.75 | P4 | 1.5 | 82 | 12.25 | 3 | 8.5 | 36.2 | 10.1 | 3 |
| M12*1.5 | P3 | 1.5 | 82 | 12.25 | 3 | 8.5 | 36.2 | 10.4 | 3 |
| M12*1.25 | P3 | 1.5 | 82 | 12.25 | 3 | 8.5 | 36.2 | 10.7 | 3 |
| M14*2 | P4 | 1.5 | 88 | 14 | 3 | 10.5 | 42.4 | 11.8 | 3 |
| M14*1.5 | P3 | 1.5 | 88 | 14 | 3 | 10.5 | 42.4 | 12.3 | 3 |
| M16*2 | P4 | 1.5 | 95 | 14 | 3 | 12.5 | 44.4 | 13.8 | 3 |
| M16*1.5 | P3 | 1.5 | 95 | 14 | 3 | 12.5 | 44.4 | 14.3 | 3 |
| M18*2.5 | P5 | 1.5 | 100 | 17.5 | 3 | 14 | 49.2 | 15.3 | 3 |
| M18*1.5 | P4 | 1.5 | 100 | 17.5 | 3 | 14 | 49.2 | 16.3 | 3 |
| M20*2.5 | P5 | 1.5 | 105 | 17.5 | 4 | 15 | 50.7 | 17.3 | 3 |
| M20*1.5 | P4 | 1.5 | 105 | 17.5 | 4 | 15 | 50.7 | 18.3 | 3 |
| M22*2.5 | P5 | 1.5 | 115 | 17.5 | 4 | 17 | 54 | 19.2 | 3 |
| M22*1.5 | P4 | 1.5 | 115 | 17.5 | 4 | 17 | 54 | 20.3 | 3 |
| M24*3 | P5 | 1.5 | 120 | 21 | 4 | 19 | 59 | 20.7 | 3 |
| M24*1.5 | P4 | 1.5 | 120 | 21 | 4 | 19 | 59 | 22.3 | 3 |
附件：
l7954.jpg
